Exojo Exoinox SW 45° Flat Trim: 45° inclined flat trim for finishing ceiling or wall outlets. AISI 304 stainless steel.

Exojo Exoinox SW single-to-double adapter: adapter for connecting Exoinox SW single-wall ductwork to double-wall systems. Laser-welded AISI 316L stainless steel.

Exojo Exoinox SW HH coupling sleeve: female-to-female coupling sleeve between duct modules. AISI 316L stainless steel, laser welded.

Exojo Exoinox SW MM coupling sleeve: male-to-male coupling sleeve between duct modules. AISI 316L stainless steel, laser welded.

Exojo Exoinox SW line collector with drain: sealing plug with drain outlet to evacuate condensation. AISI 316L stainless steel, laser welded.

Exojo Exoinox SW line manifold: closing cap for the lower end of the system. AISI 316L stainless steel, laser welded.

Exojo Exoinox SW 90° Tee: 90° T-piece for diverting the flue gas exhaust duct. AISI 316L stainless steel, laser welded.

Exojo Exoinox SW 90° Elbow: 90° elbow for right-angle changes of direction. Made of AISI 316L stainless steel, laser welded.

Exojo Exoinox SW 45° elbow: 45° elbow for changes of direction in installation. Manufactured from AISI 316L stainless steel, laser welded.

Exojo Exoinox SW 30° Elbow: 30° elbow for smooth changes of direction during installation. Made of AISI 316L stainless steel, laser welded.

Exojo Exoinox SW 500mm straight module: straight section of flue gas exhaust duct. Manufactured in AISI 316L stainless steel, laser welded.

Exojo Exoinox DW Series Adjustable Base Extension Set: This set of extensions with an adjustable base allows you to adjust the mounting height of the bracket. Compatible with the Exoinox DW 304 and Exoinox DW 316L series.

Exojo Exoblack DW 1000mm straight module: straight section of flue gas exhaust duct. Manufactured in matte black RAL 9005 lacquered stainless steel; 0.4mm AISI 316L inner wall, 0.5mm AISI 304 outer wall; 25mm 90kg/m³ rock wool insulation; laser welding; male-female connection with included clamp.

Exojo Exoinox SW 1000mm straight module: straight section of flue gas exhaust duct. Manufactured in AISI 316L stainless steel, laser welded.

Exojo repair spray is a high-temperature aerosol paint with a black finish, designed to touch up small marks or imperfections in the finish of the pipes and accessories of the range, both Exoleña Premium and Exopellet.

Exojo Exopellet Inox 316L Lead Roof Cover 30°-45°: lead roof cover for roofs with a slope of 30° to 45°. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L Lead Roof Cover 5°-30°: lead roof cover for roofs with a slope of 5° to 30°. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L rain collar: a cap-type roof collar for roof openings. Made of AISI 316L stainless steel, laser-welded.

Exojo Exopellet Inox 316L single-to-double adapter: a transition adapter for connecting single-wall and double-wall ducts. Made of AISI 316L stainless steel, laser-welded.

Exojo Exopellet Inox 316L Draft Stabilizer: a draft regulator that automatically stabilizes chimney draft. Made of AISI 316L stainless steel, laser-welded.

Exojo Exopellet Inox 316L horizontal discharge terminal: terminal grate for horizontal flue gas outlet. Manufactured from AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L horizontal rainproof outlet: horizontal outlet with rain protection. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L anti-backdraft terminal: This anti-backdraft cap prevents smoke from escaping due to wind. Made of AISI 316L stainless steel and laser-welded.

Exojo Exopellet Inox 316L joining clamp: a safety clamp that reinforces the connection between two sections. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L M-8 Mounting Bracket: Support clamp with M-8 thread for wall mounting. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L wall-mounted bracket: wall bracket for securing the duct to the wall. Made of AISI 316L stainless steel, laser-welded.

Exojo Exopellet Inox 316L Silicone Gasket: Replacement silicone gasket for sealing joints. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L silicone rosette: rosette with silicone gasket for ceiling or wall installation. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L ceiling light: decorative rosette/ceiling light for ceiling or wall transitions. Made of AISI 316L stainless steel, laser welded.

Extension of the Exojo Exopellet Inox 316L line: diameter expansion piece (converting from a smaller to a larger diameter) for connecting sections of different cross-sections. Manufactured from AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L HH coupling sleeve: female-to-female coupling sleeve for joining two sections. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L MM coupling sleeve: male-to-male coupling sleeve for joining two sections. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L Collector: Bottom-closing plug/collector for the flue, accessible for cleaning. Made of AISI 316L stainless steel, laser-welded.

90° tee with collector from the Exojo Exopellet Inox 316L line: 90° tee fitting with side outlet and accessible plug for cleaning. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L 90° Elbow: 90° elbow for right-angle changes of direction. Made of AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L 45° Elbow: 45° elbow for changes of direction in installation. Manufactured from AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L Extendable Module (570-940mm): This telescopic element is adjustable in length to create custom lengths. It is made of AISI 316L stainless steel and laser-welded.

Exojo Exopellet Inox 316L Extendable Module (390-540mm): This telescopic element is adjustable in length to create custom lengths. It is made of AISI 316L stainless steel and laser-welded.

Exojo Exopellet Inox 316L Straight Module 250mm: straight section of flue gas exhaust duct. Manufactured in AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L Straight Module 500mm: straight section of flue gas exhaust duct. Manufactured in AISI 316L stainless steel, laser welded.

Exojo Exopellet Inox 316L Straight Module 1000mm: straight section of flue gas evacuation duct. Manufactured in AISI 316L stainless steel, laser welded.

Exojo Exopellet telescopic roof trim: a telescopic trim set with a rosette for the roof opening. Manufactured from enamelled steel, oven-baked at 850°C, laser-welded, with a matte black finish.

Exopellet-Exoblack DW adapter from the Exojo Exopellet line: an adapter for connecting the Exopellet duct to Exoblack DW double-wall systems. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exojo Exopellet single-to-double adapter: a transition adapter for single-wall and double-wall ducting. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exojo Exopellet horizontal discharge terminal: terminal grille for horizontal flue gas outlet. Manufactured from enamelled steel, fired at 850ºC, laser welded, with a matte black finish.

Exojo Exopellet horizontal rainproof outlet: horizontal outlet with rain protection. Manufactured from enamelled steel, oven-baked at 850°C, laser-welded, with a matte black finish.

Exojo Exopellet anti-backdraft terminal: This anti-backdraft cap prevents smoke from escaping due to wind. It is manufactured from enamelled steel, oven-hardened at 850°C, laser-welded, and has a matte black finish.

Chinese-style chimney cap from Exojo's Exopellet line: Chinese-style cap, top finial for the chimney. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exojo Exopellet joining clamp: a safety clamp that reinforces the connection between two sections. Manufactured from steel, enamelled inside/outside at 850ºC, laser-welded, with a matte black finish.

Exojo Exopellet M-8 Support Bracket: Support clamp with M-8 thread for wall mounting. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exojo Exopellet line screw-on wall bracket: wall bracket for fixing the duct to the wall. Made of enamelled steel, fired at 850ºC, laser-welded, with a matte black finish.

Exojo Exopellet silicone rosette: rosette with silicone gasket for ceiling or wall installation. Manufactured from enamelled steel, oven-baked at 850ºC, laser-welded, with a matte black finish.

Exojo Exopellet 45° Flat Trim Plate: Flat trim plate at a 45° angle, for angled steps. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exopellet ceiling light from Exojo: decorative ceiling rose/ceiling light for ceiling or wall transitions. Manufactured from enamelled steel, oven-baked at 850ºC, laser-welded, with a matte black finish.

Exojo Exopellet silicone gasket: replacement silicone gasket for sealing joints. Made of enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exojo Exopellet HH coupling sleeve: female-to-female coupling sleeve for joining two sections. Manufactured from enamelled steel, fired at 850ºC, laser welded, with a matte black finish.

Exojo Exopellet MM coupling sleeve: male-to-male coupling sleeve for joining two sections. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a matte black finish.

Exojo Exopellet silicone collector: sealing cap with silicone gasket. Made of enamelled steel, inside/outside, fired at 850ºC, laser welded, with a matte black finish.

Exojo Exopellet line collector: bottom-closing plug/collector for the flue, accessible for cleaning. Manufactured from enamelled steel, inside and out, fired at 850ºC, laser-welded, with a matte black finish.

Exojo Exopellet draft stabilizer: a draft regulator that automatically stabilizes chimney draft. Manufactured from enamelled steel (interior/exterior) at 850°C, laser-welded, with a matte black finish.

135° T-fitting with Exojo Exopellet line collector: 135° T-fitting with angled side outlet and accessible plug for cleaning. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

90° T-fitting with 80mm inlet from the Exopellet line by Exojo: 90° T-fitting with a reduced side outlet of Ø80mm. Manufactured from enamelled steel, fired at 850ºC, laser welded, with a matte black finish.

Exojo Exopellet 90° tee with collector: 90° tee fitting with side outlet and accessible plug for cleaning. Manufactured from enamelled steel, fired at 850°C, laser welded, with a matte black finish.

Exojo Exopellet 90° Elbow with Inspection: 90° elbow with inspection hatch for cleaning. Manufactured from enamelled steel, fired at 850°C, laser welded, with a matte black finish.

Exojo Exopellet 90° elbow: 90° elbow for right-angle changes of direction. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exojo Exopellet 45° elbow: 45° elbow for changes of direction in installation. Manufactured from enamelled steel, fired at 850°C, laser welded, with a matte black finish.

Exojo Exopellet 30° Elbow: 30° elbow for smooth changes of direction during installation. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exojo Exopellet line reducer: a diameter reduction fitting (converting from a larger to a smaller diameter) for connecting sections of different cross-sections. Manufactured from steel, enamelled inside/outside at 850ºC, laser-welded, with a matte black finish.

Exojo Exopellet line expansion: a diameter expansion piece (converting from a smaller to a larger diameter) for connecting sections of different cross-sections. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exojo's Exopellet 540mm extendable module: a telescopic element adjustable in length for custom-sized sections. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a matte black finish.

Exojo Exopellet 940mm extendable module: telescopic element adjustable in length, for custom-sized sections. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a matte black finish.

Exojo Exopellet 250mm straight module: straight section of flue gas evacuation duct. Manufactured from enamelled steel, fired at 850ºC, laser welded, with a matte black finish.

Exojo Exopellet 500mm straight module: straight section of flue gas evacuation duct. Manufactured from enamelled steel, fired at 850ºC, laser welded, with a matte black finish.

Exojo Exopellet 1000mm straight module: straight section of flue gas evacuation duct. Manufactured from enamelled steel, inside/outside, at 850ºC, laser welded, with a matte black finish.

Exojo Exoleña line extractor terminal: terminal with mechanical fume extractor. Manufactured in enamelled steel, inside/outside, at 850ºC, laser welded, with a glossy black finish.

Exojo Exoleña anti-backdraft chimney cap: This anti-backdraft cap prevents smoke from entering the room due to wind. It is made of enamelled steel, fired at 850°C, laser-welded, and finished with a glossy black coating.

Chinese-style chimney cap from the Exojo Exoleña line: Chinese-style cap, top finial for the chimney. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exoleña-Exoinox DW adapter from the Exoojo Exoleña line: adapter piece for connecting Exoleña ductwork to Exoinox DW double-wall systems. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exojo Exoleña M-8 Bracket: Support clamp with M-8 thread for wall mounting. Manufactured from enamelled steel, fired at 850ºC, laser welded, with a glossy black finish.

Exojo Exoleña line screw-on wall bracket: wall bracket for fixing the duct to the wall. Made of enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exojo Exoleña line ceiling light: decorative ceiling rose/ceiling light for ceiling or wall transitions. Manufactured from enamelled steel, oven-baked at 850ºC, laser-welded, with a glossy black finish.

Exojo Exoleña HH coupling sleeve: female-to-female coupling sleeve for joining two sections. Manufactured from enamelled steel, fired at 850ºC, laser welded, with a glossy black finish.

Exojo Exoleña MM coupling sleeve: male-to-male coupling sleeve for joining two sections. Manufactured from enamelled steel, fired at 850ºC, laser welded, with a glossy black finish.

Exojo Exoleña line expansion: diameter expansion piece (converting from a smaller to a larger diameter) for connecting sections of different cross-sections. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exojo Exoleña line collector: bottom-closing plug/collector for the pipe, accessible for cleaning. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exojo Exoleña line draft stabilizer: a draft regulator that automatically stabilizes chimney draft. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exojo Exoleña 90° Tee: 90° tee fitting with side outlet. Manufactured from enamelled steel, fired at 850°C, laser welded, with a glossy black finish.

Exojo Exoleña 90° Elbow: Flexible 90° wavy elbow for changes of direction. Manufactured from enamelled steel, fired at 850°C, laser welded, with a glossy black finish.

Exojo Exoleña 45° Elbow: Flexible 45° wavy elbow for small changes of direction. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a glossy black finish.

Exojo Exoleña 90° Elbow: 90° elbow for right-angle changes of direction. Manufactured from enamelled steel, fired at 850°C, laser-welded, with a glossy black finish.

Exojo Exoleña 45° Elbow: 45° elbow for changes of direction in installation. Manufactured from enamelled steel, fired at 850°C, laser welded, with a glossy black finish.

Exojo's Exoleña anti-condensation starter module: This starter module features an anti-condensation chamber to prevent condensate dripping during flue start-up. It is manufactured from enamelled steel, fired at 850°C, laser-welded, and finished with a glossy black coating.

Exojo's Exoleña 330mm extendable module: a telescopic element adjustable in length for custom-sized sections. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

1000mm straight duct module with regulator from the Exojo Exoleña line: straight section of duct with integrated draft regulator. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exojo Exoleña 1000mm straight module: straight section of flue gas exhaust duct. Manufactured in enamelled steel, inside/outside, at 850ºC, laser welded, with a glossy black finish.

Exoleña-Exoinox DW adapter from the Exoojo Exoleña Premium line: adapter piece for connecting Exoleña ductwork to Exoinox DW double-wall systems. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exoleña-Exoblack DW adapter from the Exojo Exoleña Premium line: adapter piece for connecting Exoleña ductwork to Exoblack DW double-wall systems. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exojo's Exoleña Premium anti-backdraft chimney cap: This anti-backdraft cap prevents smoke from entering the room due to wind. It is made of enamelled steel, oven-hardened at 850°C, laser-welded, and has a glossy black finish.

Chinese-style chimney cap from Exojo's Exoleña Premium line: Chinese-style cap, top trim for the chimney. Manufactured from enamelled steel, fired at 850ºC, laser-welded, with a glossy black finish.

Exojo's Exoleña Premium telescopic ceiling trim: a telescopic trim set with a ceiling rose. Manufactured from enamelled steel, oven-baked at 850°C, laser-welded, with a glossy black finish.